Our cold-rolled products are tailored to deliver the optimum in structural and safety performance in conjunction with our services for lightweighting and cost reduction.
We place special emphasis on meeting the Class A surface finish requirements of our customers.
Coupled with consistent quality, our wide product selection provides opportunities for you to optimise both your products and processes. The benefits of our cold-rolled steel include:
- consistent and reliable end product quality
- lighter and stronger products
- repeatable, trouble-free processing
- maximised yield
- reduced waste and rework
Body and closure panels
Interior and trim
Automotive components
Grades
This section of the catalogue shows the grades of cold-rolled steel offered by Tata Steel. These include grades for forming, high-strength steels and advanced and ultra high-strength steels.
Supply – product conditions
We supply cold-rolled steel in the following conditions:
- annealed and skin-passed
- full hard
- sheets, discs and slit wide coil
Tata Steel produces cold-rolled and annealed strip by either the
continuously-annealed (CA) or batch-annealed (BA) processes.
Surface quality A
Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration.
Surface quality B
The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details.
Inspected side
As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.
Surface texture/roughness
Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.
|
|
Roughness Ra (µm) |
|
|---|---|---|
|
EN 10130: 2006 Grade |
Symbol |
cut off 0.8 mm |
|
extra-bright 1 |
- |
≤ 0.3 |
|
bright |
b |
≤ 0.4 |
|
semi-bright |
g |
≤ 0.9 |
|
normal |
m |
0.6 - 1.9 |
|
rough |
r |
> 1.6 |
|
extra rough 1 |
- |
> 2.5 |
1. Not in EN 10130:2006 - Tata Steel’s own specification.
Other surface textures are available to meet your requirements - please contact us for details
Preservative oil
The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.
Surface cleanliness
Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.
Cold-rolled: Steel for forming
CAPL range
Cold-rolled: AHSS-UHSS
DP600
DP800 (EN) / DP800 (DE)
DP1000LY-UC (EN) / DP1000LY-UC (DE)
XPF range
22MnB5
Sales terms and conditions
English
Strip products produced in IJmuiden
Strip products produced in the UK
Dutch
Strip products produced in IJmuiden
Deutsch
Strip products produced in IJmuiden
Français
Strip products produced in IJmuiden
Cold-rolled product families
EN-Automotive-Product-Cold-rolled-Forming TSE
Steel for forming
Cold-rolled steel for cold forming and deep drawing is available in a range of grades. Each grade is designed for particular applications – allowing you to pick the best steel for your product.
Our forming steel is available in a choice of widths up to 2050 mm and thicknesses up to 3.1 mm. This provides opportunities for cutting waste and maximising yield. These products are made using batch annealing (BA).
EN-Automotive-Product-Cold-rolled-HSS TSE
CR: High-strength steel
Tata Steel offers a range of cold-rolled steels for applications requiring high strength without the weight penalty.
The range comprises micro-alloyed and rephosphorised high-strength steels in cold-rolled uncoated condition.
These steels are ideal for strong, thin-gauge products.
EN-Product-Cold-rolled-AHSS TSE delete (no offering NL)
Webpage delete: AHSS/UHSS steel
Our cold-rolled dual phase and hot forming grades include advanced (AHSS) and ultra high-strength steels (UHSS)
Originally developed for the demanding automotive market, they also meet a variety of performance and processing requirements for other advanced applications.
Our advanced and ultra high-strength cold-rolled steels DP600, DP800 and 22MnB5 are lightweight and enable design freedom for complex body in white (BIW) parts.
EN_US-Automotive-Product-Metallic coated HOMEPAGE
Tata Steel offers a wide choice of metallic coated steel. Our product range includes forming and structural grades, and high-strength and advanced high-strength steels.
EN_US-Automotive-Product-Ymagine Direct-rolled-HSS TSN
High-strength steel
Ymagine® direct-rolled steel comes in five high-strength, low-alloy (HSLA) grades offering either weight savings or enhanced product strength without weight penalties.
EN_US-Automotive-Product-Hot-rolled HOMEPAGE TSE
Hot-rolled steel offers performance, versatility and value. Our hot-rolled strip steel range includes forming and high-strength, advanced and ultra high-strength steels.
EN_US-Automotive-Contact-General sales - Automotive - general
Automotive sales enquiries and customer services
Please contact us for further information, questions and enquiries. Working together on sustainable vehicles and value chains.